Circular saw blade sharpening service.
TCT carbide-tipped blades restored to clean-cut performance. Crosscut, rip, mitre, panel and combination blades, with every tooth ground individually on a precision saw-tooth grinder. Joinery shops, kitchen-makers and tradies across Australia.

Per blade,every tooth ground.
160–200mm blade
Hand-held circular saw blades, 24–48 teeth
210–254mm blade
Mitre and table saw blades, common 60–80 tooth
255–305mm blade
Larger mitre and rip blades, 60–96 tooth
Panel saw 315mm+
Panel saw blades for cabinet shops
Triple-chip / specialty
Triple-chip grind, hi-ATB, custom (quoted per blade)
Side-grind only (tip OK)
Tip-good blades that just need a side-grind
Indicative starting prices, exclusive of GST. Final quote confirmed when your gear arrives. Bulk and trade discounts available.
Every tooth individually ground on a precision saw-tooth grinder.
A new mid-range 254mm TCT blade is $80–$150. Sharpening that same blade for $32–$38 restores it to clean-cut performance, and most blades can be sharpened five to eight times before the carbide is too thin to grind.
Top and face angles, hook, gullet depth and side-clearance are all preserved. We don't change the tooth count or grind profile: a 60-tooth ATB blade comes back as a 60-tooth ATB blade.
- Top, face and hook angles preserved
- Carbide tips sharpened, not replaced
- Cheaper than buying new, every time

One workshop,every kind of edge.
Circular Saw Blade Sharpening FAQs
Common questions from joiners, cabinetmakers and tradies.
- How much does it cost to sharpen a circular saw blade in Australia?
- Hand-held circular saw blades (160–200mm) from $25. Mitre/table saw blades (210–305mm) $32–$38. Panel saw blades (315mm+) from $55. Triple-chip and specialty grinds are quoted per blade. Side-grind-only (when the tip is fine but the side has lost clearance) is $18. All prices are plus GST.
- How many times can a TCT blade be sharpened?
- Most quality TCT blades can be sharpened 5–8 times before the carbide tips are too thin to safely grind. Cheap thin-kerf blades may only take 2–3 sharpens. We measure the remaining carbide on each tooth and let you know if a blade is at the end of its life.
- Can you sharpen a blade with chipped or missing teeth?
- Yes, small chips on most teeth are routine and ground out. A single missing tooth is fine; the blade still cuts. Two or three missing teeth in a row affects balance and we'll let you know before grinding.
- Do you handle triple-chip grind (TCG) blades?
- Yes. TCG, ATB, FTG and combination grinds are all sharpened to original profile. TCG blades for ferrous metal and laminate are priced individually because each tooth has a different grind angle than the next.
- Can tungsten carbide be sharpened?
- Yes, with diamond. Carbide is too hard for ordinary grinding wheels, so tungsten carbide-tipped saw blades are sharpened on a diamond wheel one tooth at a time, keeping the top, face, hook and side angles. Each sharpen removes a little carbide, and most quality blades take 5 to 8 sharpens before the tips are too thin to grind safely.
- How do I post saw blades safely?
- Slip each blade into a cardboard sleeve (we send these out, or use the manufacturer's box). Wrap multiple blades together so the teeth don't contact each other. Rigid box only, never a soft mailer. Australia Post Express is fastest; flat-rate satchels work well for 1–3 blades. Send with Australia Post, as couriers can't deliver to our PO Box.
- What about steel blades (non-carbide)?
- Yes. Older steel blades (no carbide tips) are sharpened on the same precision grinder. Less common now but still around in workshops. Typical pricing is the same per-diameter band.

Send Your Blades In.
Turnaround is 7 to 11 business days. Joinery shops welcome. Bulk pricing on 5+ blades.
Post to PO Box 69, Gunning NSW 2581. Send with Australia Post. Couriers can't deliver to a PO Box.
Start My Order